1 radiation hardened 8-channel source driver is-2981rh, is-2981eh the star*power radiation hardened is-2981rh, is-2981eh are monolithic devices designed for use in high-side switching applications that benefit from separate grounds for the logic and loads. the devices have a 5v to 80v operating supply voltage range and is capable of sourcing -200ma continuously from each output. the outputs are controlled by active-high inputs and may be paralleled to increase the drive current. the output clamp diodes prevent device damage, when switching inductive loads. constructed with the intersil bonded wafer, dielectrically isolated hvtdlm process, these single event latch-up immune devices have been specifically designed to provide highly reliable performance in harsh radiation environments. they are fully guaranteed for 100krad(si) high dose rate and 50krad(si) low dose rate total dose performance through wafer-by-wafer radiation testing, and are production tested over the full military temperature range. specifications for rad hard qml devices are controlled by the defense logistics agency land and maritime (dla). the smd numbers listed below must be used when ordering. detailed electrical specifications for these devices are contained in smd 5962-00520 . a ?hot-link? is provided on our homepage for downloading features ? electrically screened to smd # 5962-00520 ? qml qualified per mil-prf-38535 requirements ?radiation environment - single event latch-up immune di process - high dose rate . . . . . . . . . . . . . . . . . . . . . . . . . . 100krad(si) - low dose rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50krad(si) ? input voltage range . . . . . . . . . . . . . . . 0.0v to v cc (20v max) ? supply voltage range . . . . . . . . . . . . . . . . . . . . . . . . . 5v to 80v ? turn-on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . 2s (max) ? turn-off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . 11s (max) ? output clamp diode, v f . . . . . . . . . . . . . . . . . . . . .-1.75v (max) applications ? drivers for various loads - relays, solenoids and motors ? reliable replacement of discrete solutions ? interfacing between low-level logic and high-current loads pin configuration is1-2981rh-q, is1-2981eh-q (cdip2-t18) top view tm 10 11 12 13 14 15 16 17 18 9 8 7 6 5 4 3 2 1 out 1 out 3 out 4 out 5 out 6 out 7 out 8 out 2 gnd in 1 in 2 in 3 in 4 in 5 in 6 in 8 in 7 v cc caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | copyright intersil americas llc 2000, 2013. all rights reserved intersil (and design) is a trademark owned by intersil corporation or one of its subsidiaries. all other trademarks mentioned are the property of their respective owners. june 24, 2013 fn4869.1
is-2981rh, is-2981eh 2 fn4869.1 june 24, 2013 ordering information ordering number (note 3) internal mkt.number (notes 1, 2) part marking temp. range ( c) package (rohs compliant) pkg. dwg. # 5962r0052001vvc is1-2981rh-q q 5962r00 52001vvc -55 to +125 18 ld sbdip d18.3 5962r0052002vvc is1-2981eh-q q 5962r00 52002vvc -55 to +125 18 ld sbdip d18.3 5962r0052001qvc is1-2981rh-8 q 5962r00 52001qvc -55 to +125 18 ld sbdip d18.3 5962r0052001v9a IS0-2981RH-Q -55 to +125 die 5962r0052002v9a is0-2981eh-q -55 to +125 die d18.3 is1-2981rh/proto is1-2981rh/proto is1-2981rh/proto -55 to +125 18 ld sbdip d18.3 note: 1. these intersil pb-free hermetic packaged products employ 100% au plate - e4 termination finish, which is rohs compliant and compatible with both snpb and pb-free soldering operations. 2. for moisture sensitivity level (msl), please see device information page for is-2981rh , is-2981eh . for more information on msl, please see tech brief tb363 . 3. specifications for rad hard qml devices are controlled by the defense logistics agency land and maritime (dla). the smd numbe rs listed in the ?ordering information? table on page 2 must be used when ordering.
is-2981rh, is-2981eh 3 fn4869.1 june 24, 2013 die characteristics die dimensions: 2667 m x 5131 m (105 mils x 202 mils) thickness: 483 m 25.4 m (19 mils 1 mil) interface materials glassivation type: nitride (si 3 n 4 ) over silox (sio 2 ) nitride thickness: 4.0k ? 1.0k ? silox thickness: 12.0k ? 4.0k ? metallization top metal 2: ti/alcu thickness: 1.6 m 0.02 m metal 1: ti/alcu thickness: 0.8 m 0.01 m substrate hvtdlm, bonded wafer, dielectric isolation backside finish silicon assembly related information substrate potential must be tied to gnd. additional information worst case current density <1.0 x 10 5 a/cm 2 transistor count 68 metallization mask layout is-2981rh, is-2981eh 8765 43 2 1 9 9 10 11 12 13 14 15 16 17 18 10 10a 9 9 notes: 4. pad numbers correspond to package pin functions. 5. bond to all four pad 9 locations for v cc current sharing purposes. 6. bond to both pad 10 locations for gnd current sharing purposes. 7. pad 10a is not used in die applications. 8. die backside must be connected to gnd.
is-2981rh, is-2981eh 4 intersil products are manufactured, assembled and tested utilizing iso9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality intersil products are sold by description only. intersil corporat ion reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnished by intersil is believed to be accurate and reliable. however, no responsi bility is assumed by intersil or its subsid iaries for its use; nor for any infringem ents of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of i ntersil or its subsidiaries. for information regarding intersil corporation and its products, see www.intersil.com fn4869.1 june 24, 2013 for additional products, see www.intersil.com/product_tree ceramic dual-in-line me tal seal packages (sbdip) notes: 1. index area: a notch or a pin one identification mark shall be locat- ed adjacent to pin one and shall be located within the shaded area shown. the manufacturer?s identification shall not be used as a pin one identification mark. 2. the maximum limits of lead di mensions b and c or m shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 3. dimensions b1 and c1 apply to lead base metal only. dimension m applies to lead plating and finish thickness. 4. corner leads (1, n, n/2, and n/2+1) may be configured with a partial lead paddle. for this co nfiguration dimension b3 replaces dimension b2. 5. dimension q shall be measured from the seating plane to the base plane. 6. measure dimension s1 at all four corners. 7. measure dimension s2 from the top of the ceramic body to the nearest metallization or lead. 8. n is the maximum number of terminal positions. 9. braze fillets shall be concave. 10. dimensioning and tolerancing per ansi y14.5m - 1982. 11. controlling dimension: inch. bbb c a - b s c q l a seating base d plane plane s s -d- -a- -c- e a -b- aaa ca - b m d s s ccc ca - b m d s s d e s1 b2 b a e m c1 b1 (c) (b) section a-a base lead finish metal e a/2 s2 m a d18.3 mil-std-1835 cdip2-t18 (d-6, configuration c) 18 lead ceramic dual-in-line metal seal package symbol inches millimeters notes min max min max a - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 d - 0.960 - 24.38 - e 0.220 0.310 5.59 7.87 - e 0.100 bsc 2.54 bsc - ea 0.300 bsc 7.62 bsc - ea/2 0.150 bsc 3.81 bsc - l 0.125 0.200 3.18 5.08 - q 0.015 0.070 0.38 1.78 5 s1 0.005 - 0.13 - 6 s2 0.005 - 0.13 - 7 90 o 105 o 90 o 105 o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - m - 0.0015 - 0.038 2 n18 188 rev. 0 5/18/94
|
